The great thing about having a keypad lock like the Schlage Connect is that you don’t need physical keys at all. Instead, you just enter in a key code (aka user codes) and you’re off to the races. Here’s how to create and manage key codes for the Schlage Connect smart lock, both on the lock itself and on your phone.

像Schlage Connect这样的键盘锁的好处在于，您根本不需要物理键。 取而代之的是，您只需要输入一个关键代码(又称用户代码)即可参加比赛。 这是在锁本身和手机上为Schlage Connect智能锁创建和管理键码的方法。

Before we begin, you’ll need to know your lock’s programming code, which can be found on the back of the interior portion of the unit. You should have jotted it down before installing the lock in the first place, but if not, you’ll need to take it apart and write down the programming code. This is required to put the lock into programming mode, which allows you to change and manage the lock’s settings.

在开始之前，您需要了解锁的编程代码，该代码可以在设备内部的背面找到。 首先安装锁之前，应该先将其记下，但如果没有，则需要将其拆开并写下编程代码。 这是使锁进入编程模式所必需的，它允许您更改和管理锁的设置。

如何添加用户代码 (How to Add a User Code)

The Schlage Connect comes with a couple of default codes out of the box, but it’s best to come up with your own code to use.

Schlage Connect开箱即用，带有一些默认代码，但是最好提供自己的代码来使用。

To get started, open your door and extend the deadbolt so that it’s in the locked position (you’ll begin all programming this way). From there, press down on the Schlage button at the top of the keypad and then enter in your six-digit programming code (again, you’ll begin all programming this way).

首先，请打开门并扩展锁舌，使其处于锁定位置(您将以这种方式开始所有编程)。 从那里，按下键盘顶部的Schlage按钮，然后输入六位数的编程代码(同样，您将以这种方式开始所有编程)。

After pressing the Schlage button and entering in your programming code, press “1” and then enter in the new user code that you want to use twice. So if you wanted your new user code to be 1234, you would enter in 12341234. (Note: please don’t use 1234 as your door code.)

按下Schlage按钮并输入您的编程代码后，按“ 1”，然后输入要使用两次的新用户代码。 因此，如果您希望新的用户密码为1234，请输入12341234。(注意：请不要使用1234作为您的门密码。)

If successful, the green checkmark will blink twice and you’ll also hear two beeps. If you get a red X, press the Schlage button to start over.

如果成功，绿色复选标记将闪烁两次，并且您还将听到两声哔声。 如果出现红色的X，请按Schlage按钮重新开始。

To add a user code using your phone, you’ll first need to connect the smart lock to a smarthome hub. In my case, I’m using the Wink Hub 2 along with the Wink app. Take a look at our setup guide on how to do this. You can use a different hub, and it should follow a somewhat similar process.

要使用手机添加用户代码，您首先需要将智能锁连接到智能家居集线器。 就我而言，我正在使用Wink Hub 2和Wink应用程序。 请参阅我们的设置指南 ，了解如何执行此操作。 您可以使用其他集线器，并且集线器应遵循类似的过程。

Select your lock in the app and then tap on the arrow off to the right.

在应用程序中选择您的锁，然后点击右边的箭头。

You may need to enter in your Wink password before continuing, but once that’s done, you’ll get to the User Codes screen. Tap on “Add a User Code”.

在继续操作之前，您可能需要输入Wink密码，但是一旦完成，您将进入“用户代码”屏幕。 点击“添加用户代码”。

Type in the new user code. You’ll need to enter in twice to confirm.

输入新的用户代码。 您需要输入两次以确认。

After that, give the user code a name, as well as a reminder if you ever need to delete it in the near future. Then hit “Done”.

之后，给用户代码起一个名字，并提醒您是否需要在不久的将来删除它。 然后点击“完成”。

如何删除用户代码 (How to Delete a User Code)

To delete a user code on the lock itself, press the Schlage button followed by the programming code, and then hit “2”.

要删除锁本身上的用户代码，请按Schlage按钮，再按编程代码，然后单击“ 2”。

After that, enter in the user code that you want to delete twice. If successful, you’ll get a blinking green checkmark and two beeps.

之后，输入要删除两次的用户代码。 如果成功，您将获得一个闪烁的绿色对勾和两次蜂鸣声。

You can also delete all user codes at once by pressing the Schlage button, entering in the programming code, pressing “6”, and then entering in the programming code again. This will prevent you from unlocking your door with a user code (since there are none) until you create a new user code.

您还可以通过按Schlage按钮，输入编程代码，按“ 6”，然后再次输入编程代码一次删除所有用户代码。 这将防止您使用用户代码(因为没有密码)解锁门，直到您创建新的用户代码。

To delete a user code on your phone, tap on the arrow off to the right to access the lock’s user codes. From there, tap on the user code that you want to delete.

要删除手机上的用户密码，请点按右侧关闭的箭头，以访问锁的用户密码。 在此处，点击要删除的用户代码。

Then tap “Delete This Code”.

然后点击“删除此代码”。

如何更改用户代码长度 (How to Change the User Code Length)

The Schlage Connect allows you to use anywhere from four-digit user codes up to eight-digit user codes. Keep in mind, though, that changing the user code length will also erase all current user codes, so you’ll have to create new codes after you do this.

Schlage Connect允许您在四位数用户代码到八位数用户代码之间的任何位置使用。 但是请记住，更改用户代码长度也会删除所有当前用户代码，因此您必须在执行此操作后创建新代码。

To change the length, press the Schlage button, enter in the programming code followed by “8”, and then hit the number on the keypad that corresponds to the length you want to use (you’ll press this number twice). So if you want six-digit user codes, you’ll press 66. If successful, you’ll get a blinking green checkmark and two beeps.

要更改长度，请按Schlage按钮，在编程代码中输入“ 8”，然后按键盘上与您要使用的长度相对应的数字(您将按两次该数字)。 因此，如果要输入六位数的用户代码，请按66。如果成功，您将获得闪烁的绿色对勾和两次蜂鸣声。

To change the user code length on your phone, tap on the arrow off to the right to access the lock’s user codes and select “User Code Length”.

要更改手机上的用户密码长度，请点击右边的箭头以访问锁的用户密码，然后选择“用户密码长度”。

Select a number between four and eight and then tap on “Set User Code Length”.

选择一个介于4到8之间的数字，然后点击“设置用户代码长度”。

Remember, this will delete all current user codes, so you’ll need to go back and create new ones when you do this.

请记住，这将删除所有当前用户代码，因此您需要返回并创建新的用户代码。

翻译自: https://www.howtogeek.com/331766/how-to-create-and-manage-user-codes-for-the-schlage-connect-smart-lock/