需要用到锐捷的ac管理2台ap。记录一下。

参考文档

1、确认AC无线交换机和AP是同一个软件版本，使用Ruijie>show verison 查看。

由于两台ap版本不同，一台ap220-E，一台ap220-E(M)，所以从V10升级到V11.4需要的镜像不同。如果都使用同一个镜像，可能会升级失败。

2、确认AP是工作在廋模式下，使用Ruijie>show ap-mode 验证，显示fit是廋模式。

3、有两台ap，一个使用直流电源供电，与ac直连，网口act等亮；另外一台ap通过poe电源与ac相连，act等不良，网速自适应失败。需要手动配置成100M网速才可以连接。

4、 使用tftp升级，防火墙不能关闭，不能使用，添加特例，给tftp权限。

Ruijie>enable

Password:

Ruijie#con

Enter configuration commands, one per line. End with CNTL/Z.

Ruijie(config)#sh ip int b

Interface IP-Address(Pri) IP-Address(Sec) Status Protocol

BVI 1 192.168.101.4/24 no address up up

Ruijie(config)#

Ruijie(config)#

Ruijie(config)#

Ruijie(config)#ex

*Jan 1 00:03:18: %SYS-5-CONFIG_I: Configured from console by console

Ruijie#

Ruijie#

Ruijie#ping 3.3.3.3

Sending 5, 100-byte ICMP Echoes to 3.3.3.3, timeout is 2 seconds:

< press Ctrl+C to break >

.

Success rate is 0 percent (0/1).

Ruijie#

Ruijie#sh int status

Interface Status Vlan Duplex Speed Type

-------------------------------- -------- ---- ------- --------- ------

GigabitEthernet 0/1 down 1 Unknown Unknown copper

Dot11radio 1/0 up AUTO AUTO copper

Dot11radio 2/0 up AUTO AUTO copper

Mobile-Tunnel 1 up AUTO AUTO copper

Mobile-Tunnel 2 up AUTO AUTO copper

WBI 1/0 up AUTO AUTO copper

WBI 1/1 up AUTO AUTO copper

WBI 1/2 up AUTO AUTO copper

WBI 1/3 up AUTO AUTO copper

WBI 1/4 up AUTO AUTO copper

WBI 2/0 up AUTO AUTO copper

WBI 2/1 up AUTO AUTO copper

WBI 2/2 up AUTO AUTO copper

WBI 2/3 up AUTO AUTO copper

WBI 2/4 up AUTO AUTO copper

Ruijie#

Ruijie#

Ruijie#

Ruijie#

Ruijie#con

Ruijie(config)#int gigabitEthernet 0/1

#将ap端口网速设置成100M

Ruijie(config-if-GigabitEthernet 0/1)#speed 100

Ruijie(config)#sh int st

Ruijie(config)#sh int status

*Jan 1 00:03:45: %LINK-3-UPDOWN: Interface GigabitEthernet 0/1, changed state to up.

*Jan 1 00:03:45: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet 0/1, changed state to up.

Interface Status Vlan Duplex Speed Type

-------------------------------- -------- ---- ------- --------- ------

GigabitEthernet 0/1 down 1 Unknown Unknown copper

Dot11radio 1/0 up AUTO AUTO copper

Dot11radio 2/0 up AUTO AUTO copper

Mobile-Tunnel 1 up AUTO AUTO copper

Mobile-Tunnel 2 up AUTO AUTO copper

WBI 1/0 up AUTO AUTO copper

WBI 1/1 up AUTO AUTO copper

WBI 1/2 up AUTO AUTO copper

WBI 1/3 up AUTO AUTO copper

WBI 1/4 up AUTO AUTO copper

WBI 2/0 up AUTO AUTO copper

WBI 2/1 up AUTO AUTO copper

WBI 2/2 up AUTO AUTO copper

WBI 2/3 up AUTO AUTO copper

WBI 2/4 up AUTO AUTO copper

Ruijie(config)#

Ruijie(config)#ex

*Jan 1 00:03:50: %SYS-5-CONFIG_I: Configured from console by console

Ruijie#

Ruijie#wr

*Jan 1 00:03:51: %CAPWAP-6-STATE_CHANGE: Capwap discovery state changed, from to

*Jan 1 00:03:51: %CAPWAP-6-STATE_CHANGE: Capwap discovery state changed, from to

*Jan 1 00:03:52: %CAPWAP-6-STATE_CHANGE: (peer - 1) [3.3.3.3] capwap state changed, from to

*Jan 1 00:03:52: %CAPWAP-6-STATE_CHANGE: (peer - 1) [3.3.3.3] capwap state changed, from to

*Jan 1 00:03:52: %CAPWAP-6-STATE_CHANGE: (peer - 1) [3.3.3.3] capwap state changed, from to

*Jan 1 00:03:52: %CAPWAP-6-STATE_CHANGE: (peer - 1) [3.3.3.3] capwap state changed, from to

*Jan 1 00:03:52: %CAPWAP-6-STATE_CHANGE: (peer - 1) [3.3.3.3] capwap state changed, from to

*Jan 1 00:03:52: %CAPWAP-5-PEER_NOTIFY_UP: Peer <3.3.3.3 : 5246 : 1> UP.

Building configuration...

Tony Liu

2017-12-26