【内核加载日志】

[  277.903713] jmgpu: loading out-of-tree module taints kernel.
[  277.904764] jmgpu: module verification failed: signature and/or required key missing - tainting kernel
[  277.914946] Registering platform device 'jmgpu'. Parent at platform
[  277.914968] device: 'jmgpu': device_add
[  277.914998] bus: 'platform': add device jmgpu
[  277.915036] PM: Adding info for platform:jmgpu
[  277.915207] bus: 'pci': add driver jmgpu
[  277.915236] bus: 'pci': __driver_probe_device: matched device 0000:01:00.0 with driver jmgpu
[  277.915247] bus: 'pci': really_probe: probing driver jmgpu with device 0000:01:00.0
[  277.915263] jmgpu 0000:01:00.0: no default pinctrl state
[  277.915458] checking generic (58000000 fa0000) vs hw (58000000 8000000)
[  277.915467] fb0: switching to jmgpudrmfb from EFI VGA
[  277.915523] bus: 'platform': remove device efi-framebuffer.0
[  277.915541] device: 'fb0': device_unregister
[  277.915642] PM: Removing info for No Bus:fb0
[  277.915754] device: 'fb0': device_create_release
[  277.915827] PM: Removing info for platform:efi-framebuffer.0
[  277.915909] [jmgpu] probe for 0x0731:9100
[  277.917289] [jmgpu] firmware_state info: 0x0000002f
[  277.917295] [jmgpu] software reset
[  277.939912] jmgpu_dec: subsys [0] multicorebase 0x00930000, iosize 2012
[  277.939918] jmgpu_dec: subsys [1] multicorebase 0x00950000, iosize 2012
[  277.950880] [jmgpu] found hdmi_phy cfg
[  277.951285] [jmgpu] found general cfg
[  277.951292] [jmgpu] use flash config file
[  277.951300] jmgpu 0000:01:00.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=none:owns=none
[  277.951309] driver: 'jmgpu': driver_bound: bound to device '0000:01:00.0'
[  277.951363] bus: 'pci': really_probe: bound device 0000:01:00.0 to driver jmgpu
[  277.951436] bus: 'platform': add driver jmgpu
[  277.951488] bus: 'platform': __driver_probe_device: matched device jmgpu with driver jmgpu
[  277.951495] bus: 'platform': really_probe: probing driver jmgpu with device jmgpu
[  277.951502] jmgpu jmgpu: no default pinctrl state
[  277.951701] Unable to handle kernel paging request at virtual address ffffffc02210b00a
[  277.960325] Mem abort info:
[  277.963937]   ESR = 0x96000021
[  277.967784]   EC = 0x25: DABT (current EL), IL = 32 bits
[  277.973906]   SET = 0, FnV = 0
[  277.977754]   EA = 0, S1PTW = 0
[  277.981600]   FSC = 0x21: alignment fault
[  277.986303] Data abort info:
[  277.989962]   ISV = 0, ISS = 0x00000021
[  277.994492]   CM = 0, WnR = 0
[  277.998152] swapper pgtable: 4k pages, 39-bit VAs, pgdp=00000000cfb89000
[  278.005547] [ffffffc02210b00a] pgd=100000207ffff803, p4d=100000207ffff803, pud=100000207ffff803, pmd=0068000060000f11
[  278.016857] Internal error: Oops: 96000021 [#2] SMP
[  278.022419] Modules linked in: jmgpu(OE+) xt_tcpudp l2tp_ppp l2tp_netlink l2tp_core pppox ppp_generic slhc ipt_REJECT nf_reject_ipv4 xt_conntrack nf_conntrack nf_defrag_ipv6 xfrm_user xfrm_algo nf_defrag_ipv4 libcrc32c rfkill iptable_filter bpfilter nls_iso8859_1 vfat stk3310 regmap_i2c crct10dif_ce industrialio snd_hda_codec_realtek snd_hda_codec_generic ledtrig_audio drm_kms_helper cec i2c_algo_bit i2c_phytium_platform i2c_phytium_core i2c_smbus cppc_cpufreq snd_hda_phytium snd_hda_codec snd_hda_core thermal sch_fq_codel ttm drm i2c_core ip_tables x_tables multipath linear xhci_plat_hcd(+) gpio_phytium_platform gpio_phytium_core
[  278.079008] CPU: 0 PID: 1354 Comm: insmod Tainted: G S    D    OE     5.15.44+ #10
[  278.087261] Hardware name: Greatwall GW-XXXXXX-XXX/GW-XXXXXX-XXX, BIOS F080-ETFBE02t Nov 14 2022
[  278.096728] pstate: 20000005 (nzCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[  278.104373] pc : __memcpy+0x98/0x250
[  278.108640] lr : jmgpu_adjust_param+0x3f4/0x4c8 [jmgpu]
[  278.114648] sp : ffffff9f83517770
[  278.118645] x29: ffffff9f83517770 x28: ffffff9f8286fe80 x27: ffffffc022100000
[  278.126465] x26: ffffff9f8001d000 x25: 0000000000000000 x24: 0000000000000000
[  278.134285] x23: ffffffc009076888 x22: ffffffc0010365f0 x21: ffffffc001036110
[  278.142105] x20: ffffffc001035990 x19: ffffffc0010359d0 x18: 00000000ffffffff
[  278.149925] x17: 00000000ffffffff x16: 000000000000000f x15: 0000000000000001
[  278.157744] x14: 0000000000000001 x13: 0000000000000000 x12: 0000000000000000
[  278.165564] x11: 0000000000400000 x10: ffffffc001035ff8 x9 : 2e35323031323230
[  278.173383] x8 : 322d302e312e312d x7 : 657261776d726966 x6 : 706c303031396d6a
[  278.181203] x5 : ffffff9f8286fdaa x4 : ffffffc02210b02a x3 : 000000000000002a
[  278.189023] x2 : 000000000000002a x1 : ffffffc02210b000 x0 : ffffff9f8286fd80
[  278.196844] Call trace:
[  278.199973]  __memcpy+0x98/0x250
[  278.203887]  jm_dev_probe+0x4fc/0xbd0 [jmgpu]
[  278.208979]  platform_probe+0x64/0xd0
[  278.213326]  really_probe+0xec/0x418
[  278.217588]  __driver_probe_device+0xb0/0x180
[  278.222629]  driver_probe_device+0x7c/0x108
[  278.227496]  __driver_attach+0xf0/0x178
[  278.232016]  bus_for_each_dev+0x70/0xc0
[  278.236536]  driver_attach+0x20/0x28
[  278.240794]  bus_add_driver+0x1a8/0x210
[  278.245313]  driver_register+0x60/0x110
[  278.249833]  __platform_driver_register+0x24/0x30
[  278.255220]  jm_dev_init+0x5c/0x1000 [jmgpu]
[  278.260223]  do_one_initcall+0x74/0x1c0
[  278.264743]  do_init_module+0x40/0x1f8
[  278.269179]  load_module+0x2154/0x22e0
[  278.273611]  __do_sys_finit_module+0xbc/0x120
[  278.278652]  __arm64_sys_finit_module+0x1c/0x28
[  278.283865]  invoke_syscall+0x40/0xf8
[  278.288212]  el0_svc_common.constprop.3+0x90/0xe8
[  278.293599]  do_el0_svc+0x20/0x80
[  278.297597]  el0_svc+0x1c/0x48
[  278.301338]  el0t_64_sync_handler+0x88/0xb0
[  278.306204]  el0t_64_sync+0x158/0x15c
[  278.310551] Code: d65f03c0 d503201f a9401c26 a9412428 (a97e2c8a) 
[  278.317328] ---[ end trace b7e106fa690bc18b ]---

【pci信息】

01:00.0 VGA compatible controller: Jingjia Microelectronics Co Ltd (JJM) JM9100 (rev 01) (prog-if 00 [VGA controller])
    Subsystem: Jingjia Microelectronics Co Ltd (JJM) JM9100
    Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
    Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
    Latency: 0
    Interrupt: pin A routed to IRQ 88
    Region 0: Memory at 58000000 (32-bit, non-prefetchable) [size=128M]
    Region 1: Memory at 60000000 (32-bit, non-prefetchable) [size=32M]
    Region 2: Memory at 1000000000 (64-bit, prefetchable) [size=256M]
    Region 4: Memory at 62000000 (32-bit, non-prefetchable) [size=1M]
    Region 5: I/O ports at 1000 [size=256]
    Expansion ROM at 62100000 [size=128K]
    Capabilities: [40] Power Management version 3
        Flags: PMEClk- DSI- D1+ D2- AuxCurrent=375mA PME(D0+,D1+,D2-,D3hot+,D3cold-)
        Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
    Capabilities: [50] MSI: Enable+ Count=1/1 Maskable+ 64bit+
        Address: 0000000030830040  Data: 0000
        Masking: 00000000  Pending: 00000000
    Capabilities: [70] Express (v2) Endpoint, MSI 00
        DevCap:    MaxPayload 256 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
            ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset+ SlotPowerLimit 0.000W
        DevCtl:    CorrErr- NonFatalErr- FatalErr- UnsupReq-
            RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+ FLReset-
            MaxPayload 128 bytes, MaxReadReq 512 bytes
        DevSta:    CorrErr+ NonFatalErr- FatalErr- UnsupReq- AuxPwr- TransPend-
        LnkCap:    Port #0, Speed 16GT/s, Width x8, ASPM L1, Exit Latency L1 <64us
            ClockPM- Surprise- LLActRep- BwNot- ASPMOptComp+
        LnkCtl:    ASPM Disabled; RCB 64 bytes Disabled- CommClk-
            ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
        LnkSta:    Speed 8GT/s (downgraded), Width x2 (downgraded)
            TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
        DevCap2: Completion Timeout: Range ABCD, TimeoutDis+, NROPrPrP-, LTR-
             10BitTagComp+, 10BitTagReq-, OBFF Not Supported, ExtFmt-, EETLPPrefix-
             EmergencyPowerReduction Not Supported, EmergencyPowerReductionInit-
             FRS-, TPHComp-, ExtTPHComp-
             AtomicOpsCap: 32bit- 64bit- 128bitCAS-
        DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
             AtomicOpsCtl: ReqEn-
        LnkCtl2: Target Link Speed: 16GT/s, EnterCompliance- SpeedDis-
             Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
             Compliance De-emphasis: -6dB
        LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete+, EqualizationPhase1+
             EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
    Capabilities: [100 v2] Advanced Error Reporting
        UESta:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
        UEMsk:    DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
        UESvrt:    DLP+ SDES+ TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
        CESta:    RxErr+ BadTLP+ BadDLLP+ Rollover- Timeout+ AdvNonFatalErr-
        CEMsk:    RxErr- BadTLP- BadDLLP- Rollover- Timeout- AdvNonFatalErr+
        AERCap:    First Error Pointer: 00, ECRCGenCap- ECRCGenEn- ECRCChkCap+ ECRCChkEn-
            MultHdrRecCap- MultHdrRecEn- TLPPfxPres- HdrLogCap-
        HeaderLog: 00000000 00000000 00000000 00000000
    Kernel driver in use: jmgpu
    Kernel modules: jmgpu

测试日志20221122相关推荐

  1. Python学习之道-烤机测试日志Log分析统计

    Python学习之道-烤机测试日志Log分析统计 问题引出 一.环境准备 二.实践代码 1.初步实现 2.更新CSV文件写入统计结果 3.运行脚本 4.实现遍历多个Log并汇总结果到Excel 三.遇 ...

  2. 互联网摸鱼日报(2022-11-22)

    互联网摸鱼日报(2022-11-22) InfoQ 热门话题 社交网络分析方法在恶性舆论事件分析中的应用 汽车行业场景化营销新方向:基于 WebGL 的网上虚拟车展 大数据+ VR 全景技术重塑&qu ...

  3. 20221122非累加的m3u8的ts切片列表的补全步骤

    20221122非累加的m3u8的ts切片列表的补全步骤 2022/11/22 19:07 https://apppy87xs3b3950.h5.xiaoeknow.com/v2/course/ali ...

  4. Java单元测试实践-23.Gradle单元测试日志、报告与JaCoCo代码覆盖率

    Java单元测试实践-00.目录(9万多字文档+700多测试示例) https://blog.csdn.net/a82514921/article/details/107969340 1. Gradl ...

  5. java junit 语句,java – Junit测试日志语句

    我有一个类似于foo的 java 8应用程序: import org.slf4j.Logger; import org.slf4j.LoggerFactory; public class Foo { ...

  6. Windows Live Writer 测试日志

    我是用Windows Live Writer 2011写出来的日志博文.也是我在51CTO上写的第一篇博文. 下次写博文可能就在半年后了,因为我要准备为高考而奋斗!在这里祝自己高考顺利! 转载于:ht ...

  7. 百度小程序opencard书法字典名家书法等测试日志记录

    百度小程序opencard上线后的效果如图,本文以书法字典为例 本文讲的是已经开发好了接口程序,如何进行测试. 第一步,打开百度测试的网址 https://open.baidu.com/static/ ...

  8. xshell 6查看测试日志

    --------------新建连接-------------- 1.新建链接,输入名称(起个有意义的).四个待确定的项:ip.端口.用户名.密码 IP:11.51.192.92 用户名和密码需要联系 ...

  9. 【教学类-17-01】20221122《世界杯七巧板A4整页-随机参考图+七巧板+画框》(大班)

    效果展示: 单页效果 多页效果 预设样式: 背景需求: 2022年11月20日 2022年卡塔尔世界杯足球赛在卡塔尔首都多哈举行.借此契机,我设计一份七巧板让幼儿拼"踢足球"的造型 ...

最新文章

  1. 单据自动转换并审核的方法示例
  2. 一年新增457万例,用 Python 揭示癌症的可怕之处
  3. 安装opencv3.3.0碰到的问题及解决方法
  4. 按周选择的时间控件_基金定投到底是选择按周定投好还是按月定投好,两者区别是什么?...
  5. C++类型转换基本语法
  6. canvas入门实战--邀请卡生成与下载
  7. 计算机自带游戏在哪里打开,电脑自带游戏选项在哪里打开
  8. 微信小应用资源汇总整理
  9. HTM皮质学习算法资料
  10. python是什么-什么是Python?最全的python百科
  11. 遇到INSTALL_FAILED_VERIFICATION_FAILURE怎么办
  12. 深入浅出新一代云网络——VPC中的那些功能与基于OpenStack Neutron的实现(二)-带宽控制...
  13. 量子计算机需要的基础,量子计算入门
  14. php调用谷歌翻译接口_PHP调用谷歌翻译
  15. freewitch测试信息-cdr
  16. android 微信地图定位失败,微信端H5使用百度地图定位获取当前位置安卓定位不准...
  17. 求两条轨迹间的hausdorff距离_【每周三题】高二【136】分子间作用力和分子势能...
  18. 学生信息管理系统 jsp + servlet + mysql (2020)
  19. 多硬盘分区管理fdisk-张丹
  20. 国外问卷调查是骗人的吗?

热门文章

  1. 图片怎么转为html5,将图片转化为矢量并canvas化的容易工具(基于Node.js + HTML5 canvas)...
  2. paip.信用卡账单处理分类bug o21
  3. React项目创建以及结构
  4. 不知道如何进行整篇文档翻译?尝试一下这几款软件吧
  5. 微信小程序注册流程(企业注册)
  6. Kubernetes中部署MySQL高可用集群
  7. IPC网络摄像机开发
  8. Android 开发之 手势开发
  9. 试用了阿里云市场的验证码识别api,真的牛批,传统4位数验证码识别率超高
  10. 电子顺磁共振ESR测试