NETDMIS5.0 程序结构2023
2024-05-18 01:42:52
1 ,测量设置
手动模式、测头、接近/回退距离、触测/移动速度等
$$ NET_DMIS_20160720
$$ MADE IN DE 2023-2-23 9:25:24
INCLUD/DMIS,'NET_DMIS_DEFINES.DMI'
INCLUD/DMIS,'VARDEFINE'
DMESW/COMAND,'PROBE_VAL/INIT'
UNITS/MM,ANGDEC
D(MACHINE)=DATSET/MCS
DMESW/COMAND,'COORDSYS/ALIGN'
WKPLAN/XYPLAN
PRCOMP/ON
PRCOMP/ON
FEDRAT/POSVEL,MMPS,300.0000
ACLRAT/POSACL,MMPSS,100.0000
FEDRAT/MESVEL,MMPS,20.0000
ACLRAT/MESACL,MMPSS,100.0000
SNSET/RETRCT,1.0000
SNSET/SEARCH,5.0000
SNSET/APPRCH,1.0000
DMESW/COMAND,'SNSET/MANRETRCT,1.0000'
DMESW/COMAND,'REPORT/CLEAR'
MODE/MAN
DID(D2L40)=DEVICE/STOR,'D2L40'
OPEN/DID(D2L40),SNS
S(A0B0)=SNSDEF/PROBE,INDEX,POL,0.0,0.0,0.0000,0.0000,1.0000,189.6500,2.0000
SNSLCT/SA(A0B0)
FEDRAT/MESVEL,MMPS,2.0000
SNSET/RETRCT,2.0000
SNSET/APPRCH,2.0000
DMESW/COMAND,'SNSET/MANRETRCT,2.0000'
2 ,手动测量元素，建手动坐标系（粗建坐标系）
MODE/MAN
DID(D2L40)=DEVICE/STOR,'D2L40'
OPEN/DID(D2L40),SNS
S(A0B0)=SNSDEF/PROBE,INDEX,POL,0.0,0.0,0.0000,0.0000,1.0000,189.6500,2.0000
SNSLCT/SA(A0B0)
FEDRAT/MESVEL,MMPS,2.0000
SNSET/RETRCT,2.0000
SNSET/APPRCH,2.0000
DMESW/COMAND,'SNSET/MANRETRCT,2.0000'
GEOALG/PLANE,LSTSQR
F(平面1)=FEAT/PLANE,CART,31.2650,39.5919,0,0,0,1.00000000
MEAS/PLANE,F(平面1),4
PTMEAS/CART,3.7540,55.2894,0,0,0,1.00000000
PTMEAS/CART,2.7995,4.3170,0,0,0,1.00000000
PTMEAS/CART,60.3669,5.1633,0,0,0,1.00000000
PTMEAS/CART,58.1395,93.5981,0,0,0,1.00000000
ENDMES
SNSET/DEPTH,0
DMESW/COMAND,'CONST/SET_PROJ_VEC,FA(平面1),1'
F(直线1)=FEAT/LINE,UNBND,CART,3.6651,0,-2.2385,0.99998102,0,-0.00616102,0,-1.00000000,0
MEAS/LINE,F(直线1),2
PTMEAS/CART,3.6651,0,-2.4232,0,-1.00000000,0
PTMEAS/CART,63.6273,0,-2.4232,0,-1.00000000,0
ENDMES
F(点1)=FEAT/POINT,CART,0,4.3945,-2.5726,-1.00000000,0,0
MEAS/POINT,COMP,DME,F(点1),1
PTMEAS/CART,0,4.3945,-2.5726,-1.00000000,0,0
ENDMES
DATDEF/F(平面1),DAT(A_平面1)
D(坐标系1_S)=DATSET/DAT(A_平面1),ZDIR
D(坐标系1_R)=ROTATE/ZAXIS,FA(直线1),XDIR
D(坐标系1_T)=TRANS/ZORIG,FA(平面1)
D(坐标系1_T)=TRANS/YORIG,FA(直线1)
D(坐标系1_T)=TRANS/XORIG,FA(点1)
DMESW/COMAND,'COORDSYS/CAD=PART'
SAVE/DA(坐标系1)
3 ,在DCC模式下，测量元素，建自动坐标系（精建坐标系）
MODE/AUTO,PROG,MAN
SNSET/RETRCT,1.0000
SNSET/APPRCH,1.0000
DMESW/COMAND,'CLEARP/ZDIR,10.0000,ZDIR,10.0000,ON'
F(平面2)=FEAT/PLANE,CART,32.4057,47.9193,0,0,0,1.00000000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_PLANEPOINTS_1006),AUTOFIGURE,F(平面2),PLANE,CART,LSTSQR,32.4057,47.9193,$
0,0,0,1.00000000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,POINTS,'9,2.4645,6.4585,0,0,0,1.00000000,3.1419,$
59.2458,0,0,0,1.00000000,22.8566,94.6659,0,0,0,1.00000000,58.4447,96.4369,0,0,0,1.00000000,61.7202,66.2279,$
0,0,0,1.00000000,60.3207,4.3748,0,0,0,1.00000000,21.8357,6.4613,0,0,0,1.00000000,20.9073,50.4742,0,0,$
0,1.00000000,39.9595,46.9280,0,0,0,1.00000000',TOUCH,0.3000,XYPLAN
F(直线2)=FEAT/LINE,BND,CART,4.0000,0,-2.0000,63.0000,0,-2.0000,0,-1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_LINE_1007),AUTOFIGURE,F(直线2),LINE_BND,CART,4.0000,0,-2.0000,1.00000000,$
0,0,59.0000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,0,-1.00000000,0,4,0,0,0,TOUCH,0.3000,XYPLAN,0,0,LINE,$
"","","EXT1","EXT2","EXT3",ENDCAL
F(直线3)=FEAT/LINE,BND,CART,0,4.0000,-2.0000,0,58.0000,-2.0000,-1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_LINE_1007),AUTOFIGURE,F(直线3),LINE_BND,CART,0,4.0000,-2.0000,0,1.00000000,$
0,54.0000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,-1.00000000,0,0,4,0,0,0,TOUCH,0.3000,XYPLAN,0,0,LINE,"",$
"","EXT1","EXT2","EXT3",ENDCAL
F(点2)=FEAT/POINT,CART,0,0,-2.0000,0,0,-1.00000000
CONST/POINT,F(点2),INTOF,FA(直线2),FA(直线3)
DATDEF/F(平面2),DAT(A_平面2)
D(坐标系2_S)=DATSET/DAT(A_平面2),ZDIR
D(坐标系2_R)=ROTATE/ZAXIS,FA(直线2),XDIR
D(坐标系2_T)=TRANS/XORIG,FA(点2),YORIG,FA(点2)
D(坐标系2_T)=TRANS/ZORIG,FA(平面2)
SAVE/DA(坐标系2)
4 ,测量元素
5 ,构造所需元素
6 ,评价所需形位公差
7 ,生成报告、保存和打印报告
注：第1步可以穿插在后续需要修改的位置，即可根据需要多次设计。第2步手动坐标系尽量简单,可与第3步自动坐标系一样也可不一样，第 4、5、6步可以循环排布。
$$ NET_DMIS_20160720
$$ MADE IN DE 2023-2-23 9:25:24
INCLUD/DMIS,'NET_DMIS_DEFINES.DMI'
INCLUD/DMIS,'VARDEFINE'
DMESW/COMAND,'PROBE_VAL/INIT'
UNITS/MM,ANGDEC
D(MACHINE)=DATSET/MCS
DMESW/COMAND,'COORDSYS/ALIGN'
WKPLAN/XYPLAN
PRCOMP/ON
PRCOMP/ON
FEDRAT/POSVEL,MMPS,300.0000
ACLRAT/POSACL,MMPSS,100.0000
FEDRAT/MESVEL,MMPS,20.0000
ACLRAT/MESACL,MMPSS,100.0000
SNSET/RETRCT,1.0000
SNSET/SEARCH,5.0000
SNSET/APPRCH,1.0000
DMESW/COMAND,'SNSET/MANRETRCT,1.0000'
DMESW/COMAND,'REPORT/CLEAR'
MODE/MAN
DID(D2L40)=DEVICE/STOR,'D2L40'
OPEN/DID(D2L40),SNS
S(A0B0)=SNSDEF/PROBE,INDEX,POL,0.0,0.0,0.0000,0.0000,1.0000,189.6500,2.0000
SNSLCT/SA(A0B0)
FEDRAT/MESVEL,MMPS,2.0000
SNSET/RETRCT,2.0000
SNSET/APPRCH,2.0000
DMESW/COMAND,'SNSET/MANRETRCT,2.0000'
GEOALG/PLANE,LSTSQR
F(平面1)=FEAT/PLANE,CART,31.2650,39.5919,0,0,0,1.00000000
MEAS/PLANE,F(平面1),4
PTMEAS/CART,3.7540,55.2894,0,0,0,1.00000000
PTMEAS/CART,2.7995,4.3170,0,0,0,1.00000000
PTMEAS/CART,60.3669,5.1633,0,0,0,1.00000000
PTMEAS/CART,58.1395,93.5981,0,0,0,1.00000000
ENDMES
SNSET/DEPTH,0
DMESW/COMAND,'CONST/SET_PROJ_VEC,FA(平面1),1'
F(直线1)=FEAT/LINE,UNBND,CART,3.6651,0,-2.2385,0.99998102,0,-0.00616102,0,-1.00000000,0
MEAS/LINE,F(直线1),2
PTMEAS/CART,3.6651,0,-2.4232,0,-1.00000000,0
PTMEAS/CART,63.6273,0,-2.4232,0,-1.00000000,0
ENDMES
F(点1)=FEAT/POINT,CART,0,4.3945,-2.5726,-1.00000000,0,0
MEAS/POINT,COMP,DME,F(点1),1
PTMEAS/CART,0,4.3945,-2.5726,-1.00000000,0,0
ENDMES
DATDEF/F(平面1),DAT(A_平面1)
D(坐标系1_S)=DATSET/DAT(A_平面1),ZDIR
D(坐标系1_R)=ROTATE/ZAXIS,FA(直线1),XDIR
D(坐标系1_T)=TRANS/ZORIG,FA(平面1)
D(坐标系1_T)=TRANS/YORIG,FA(直线1)
D(坐标系1_T)=TRANS/XORIG,FA(点1)
DMESW/COMAND,'COORDSYS/CAD=PART'
SAVE/DA(坐标系1)
MODE/AUTO,PROG,MAN
SNSET/RETRCT,1.0000
SNSET/APPRCH,1.0000
DMESW/COMAND,'CLEARP/ZDIR,10.0000,ZDIR,10.0000,ON'
F(平面2)=FEAT/PLANE,CART,32.4057,47.9193,0,0,0,1.00000000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_PLANEPOINTS_1006),AUTOFIGURE,F(平面2),PLANE,CART,LSTSQR,32.4057,47.9193,$
0,0,0,1.00000000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,POINTS,'9,2.4645,6.4585,0,0,0,1.00000000,3.1419,$
59.2458,0,0,0,1.00000000,22.8566,94.6659,0,0,0,1.00000000,58.4447,96.4369,0,0,0,1.00000000,61.7202,66.2279,$
0,0,0,1.00000000,60.3207,4.3748,0,0,0,1.00000000,21.8357,6.4613,0,0,0,1.00000000,20.9073,50.4742,0,0,$
0,1.00000000,39.9595,46.9280,0,0,0,1.00000000',TOUCH,0.3000,XYPLAN
GEOALG/CIRCLE,LSTSQR
DMESW/COMAND,'CONST/SET_PROJ_VEC,FA(XY),1'
F(圆8)=FEAT/CIRCLE,INNER,CART,31.5000,31.5000,-3.0000,0,0,1.00000000,36.0000
CONST/CIRCLE,F(圆8),BF,FA(圆2),FA(圆3),FA(圆4),FA(圆5),FA(圆6),FA(圆7)
F(直线2)=FEAT/LINE,BND,CART,4.0000,0,-2.0000,63.0000,0,-2.0000,0,-1.00000000,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_LINE_1007),AUTOFIGURE,F(直线2),LINE_BND,CART,4.0000,0,-2.0000,1.00000000,$
0,0,59.0000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,0,-1.00000000,0,4,0,0,0,TOUCH,0.3000,XYPLAN,0,0,LINE,$
"","","EXT1","EXT2","EXT3",ENDCAL
F(直线3)=FEAT/LINE,BND,CART,0,4.0000,-2.0000,0,58.0000,-2.0000,-1.00000000,0,0
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_LINE_1007),AUTOFIGURE,F(直线3),LINE_BND,CART,0,4.0000,-2.0000,0,1.00000000,$
0,54.0000,FALSE,FALSE,FALSE,0,"CUR",TRUE,FALSE,-1.00000000,0,0,4,0,0,0,TOUCH,0.3000,XYPLAN,0,0,LINE,"",$
"","EXT1","EXT2","EXT3",ENDCAL
F(点2)=FEAT/POINT,CART,0,0,-2.0000,0,0,-1.00000000
CONST/POINT,F(点2),INTOF,FA(直线2),FA(直线3)
DATDEF/F(平面2),DAT(A_平面2)
D(坐标系2_S)=DATSET/DAT(A_平面2),ZDIR
D(坐标系2_R)=ROTATE/ZAXIS,FA(直线2),XDIR
D(坐标系2_T)=TRANS/XORIG,FA(点2),YORIG,FA(点2)
D(坐标系2_T)=TRANS/ZORIG,FA(平面2)
SAVE/DA(坐标系2)
F(圆1)=FEAT/CIRCLE,INNER,CART,31.5000,31.5000,0,0,0,1.00000000,20.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆1),CIRCLE,INNER,CART,LSTSQR,31.5000,31.5000,$
0,0,0,1.00000000,20.0000,-1.00000000,0,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,$
FALSE,FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,1,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(圆2)=FEAT/CIRCLE,INNER,CART,31.5000,49.5000,0,0,0,1.00000000,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆2),CIRCLE,INNER,CART,LSTSQR,31.5000,49.5000,$
0,0,0,1.00000000,10.0000,-1.00000000,0,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,$
FALSE,FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,1,0,0,0,3.0000,0,10','0,1,0,$
5.0000',"EXT3",ENDCAL
F(圆3)=FEAT/CIRCLE,INNER,CART,15.9115,40.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆3),CIRCLE,INNER,CART,LSTSQR,15.9115,40.5000,$
0,0,0,1,10.0000,-0.5,-0.8660254,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,1,0,0,0,3.0000,0,10','0,1,0,5.0000',$
"EXT3",ENDCAL
F(圆4)=FEAT/CIRCLE,INNER,CART,15.9115,22.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆4),CIRCLE,INNER,CART,LSTSQR,15.9115,22.5000,$
0,0,0,1,10.0000,0.5,-0.8660254,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,1,0,0,0,3.0000,0,10','0,1,0,5.0000',$
"EXT3",ENDCAL
F(圆5)=FEAT/CIRCLE,INNER,CART,31.5000,13.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆5),CIRCLE,INNER,CART,LSTSQR,31.5000,13.5000,$
0,0,0,1,10.0000,1,0,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,FALSE,0,"CUR",$
TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,1,0,0,0,3.0000,0,10','0,1,0,5.0000',"EXT3",ENDCAL
F(圆6)=FEAT/CIRCLE,INNER,CART,47.0885,22.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆6),CIRCLE,INNER,CART,LSTSQR,47.0885,22.5000,$
0,0,0,1,10.0000,0.5,0.8660254,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,1,0,0,0,3.0000,0,10','0,1,0,5.0000',$
"EXT3",ENDCAL
F(圆7)=FEAT/CIRCLE,INNER,CART,47.0885,40.5000,0,0,0,1,10.0000
CALL/EXTERN,DMIS,M(NETDMIS_AUTO_CIRCLE_1007),AUTOFIGURE,F(圆7),CIRCLE,INNER,CART,LSTSQR,47.0885,40.5000,$
0,0,0,1,10.0000,-0.5,0.8660254,0,5,-3.0000,0,0,0,-180.0000,180.0000,TOUCH,CIRCLE,0.3000,0,FALSE,FALSE,$
FALSE,0,"CUR",TRUE,FALSE,0,FA(VECBLD),10.0000,2.5000,3,XYPLAN,"",'7,1,0,0,0,3.0000,0,10','0,1,0,5.0000',$
"EXT3",ENDCAL
T(X轴坐标)=TOL/CORTOL,XAXIS,-0.0500,0.0500
T(Y轴坐标)=TOL/CORTOL,YAXIS,-0.0500,0.0500
T(直径)=TOL/DIAM,0.0200,0.0000
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC'
DMESW/COMAND,'OUTPUT/VECTOR,OFF'
OUTPUT/FA(圆1),TA(X轴坐标),TA(Y轴坐标),TA(直径)
T(X轴坐标)=TOL/CORTOL,XAXIS,-0.0500,0.0500
T(Y轴坐标)=TOL/CORTOL,YAXIS,-0.0500,0.0500
T(直径)=TOL/DIAM,0.0200,0.0000
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC'
DMESW/COMAND,'OUTPUT/VECTOR,OFF'
OUTPUT/FA(圆2),TA(X轴坐标),TA(Y轴坐标),TA(直径)
T(X轴坐标)=TOL/CORTOL,XAXIS,-0.0500,0.0500
T(Y轴坐标)=TOL/CORTOL,YAXIS,-0.0500,0.0500
T(直径)=TOL/DIAM,0.0200,0.0000
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC'
DMESW/COMAND,'OUTPUT/VECTOR,OFF'
OUTPUT/FA(圆3),TA(X轴坐标),TA(Y轴坐标),TA(直径)
T(X轴坐标)=TOL/CORTOL,XAXIS,-0.0500,0.0500
T(Y轴坐标)=TOL/CORTOL,YAXIS,-0.0500,0.0500
T(直径)=TOL/DIAM,0.0200,0.0000
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC'
DMESW/COMAND,'OUTPUT/VECTOR,OFF'
OUTPUT/FA(圆4),TA(X轴坐标),TA(Y轴坐标),TA(直径)
T(X轴坐标)=TOL/CORTOL,XAXIS,-0.0500,0.0500
T(Y轴坐标)=TOL/CORTOL,YAXIS,-0.0500,0.0500
T(直径)=TOL/DIAM,0.0200,0.0000
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC'
DMESW/COMAND,'OUTPUT/VECTOR,OFF'
OUTPUT/FA(圆5),TA(X轴坐标),TA(Y轴坐标),TA(直径)
T(X轴坐标)=TOL/CORTOL,XAXIS,-0.0500,0.0500
T(Y轴坐标)=TOL/CORTOL,YAXIS,-0.0500,0.0500
T(直径)=TOL/DIAM,0.0200,0.0000
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
DMESW/COMAND,'OUTPUT/UNIT,ANGLE/ANGDEC'
DMESW/COMAND,'OUTPUT/VECTOR,OFF'
OUTPUT/FA(圆6),TA(X轴坐标),TA(Y轴坐标),TA(直径)
T(位置度1-RN)=TOL/CIRLTY,0.0200
T(位置度1-DF)=TOL/DIAM,0.0200,0.0000
T(位置度1)=TOL/POS,2D,0.0500,RFS
DMESW/COMAND,'TOL-NOM/位置度1,COORD/0,POLTYPE/0,FEAT/圆1,WKPLAN/XYPLAN,XAXIS/31.5000,YAXIS/31.5000,ZAXIS/-3.0000,$
PR/44.5477,PA/45.0000,DIAM/20.0000,XOUTPUT/TRUE,YOUTPUT/TRUE,ZOUTPUT/FALSE,PROUTPUT/FALSE,PAOUTPUT/FALSE,$
DOUTPUT/TRUE,FOUTPUT/FALSE'
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
OUTPUT/FA(圆1),TA(位置度1)
T(位置度2-RN)=TOL/CIRLTY,0.0200
T(位置度2-DF)=TOL/DIAM,0.0200,0.0000
T(位置度2)=TOL/POS,2D,0.0500,RFS
DMESW/COMAND,'TOL-NOM/位置度2,COORD/0,POLTYPE/0,FEAT/圆2,WKPLAN/XYPLAN,XAXIS/31.5000,YAXIS/49.5000,ZAXIS/-3.0000,$
PR/58.6728,PA/57.5288,DIAM/10.0000,XOUTPUT/TRUE,YOUTPUT/TRUE,ZOUTPUT/FALSE,PROUTPUT/FALSE,PAOUTPUT/FALSE,$
DOUTPUT/TRUE,FOUTPUT/FALSE'
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
OUTPUT/FA(圆2),TA(位置度2)
T(位置度3-RN)=TOL/CIRLTY,0.0200
T(位置度3-DF)=TOL/DIAM,0.0200,0.0000
T(位置度3)=TOL/POS,2D,0.0500,RFS
DMESW/COMAND,'TOL-NOM/位置度3,COORD/0,POLTYPE/0,FEAT/圆3,WKPLAN/XYPLAN,XAXIS/15.9115,YAXIS/40.5000,ZAXIS/-3.0000,$
PR/43.5135,PA/68.5513,DIAM/10.0000,XOUTPUT/TRUE,YOUTPUT/TRUE,ZOUTPUT/FALSE,PROUTPUT/FALSE,PAOUTPUT/FALSE,$
DOUTPUT/TRUE,FOUTPUT/FALSE'
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
OUTPUT/FA(圆3),TA(位置度3)
T(位置度4-RN)=TOL/CIRLTY,0.0200
T(位置度4-DF)=TOL/DIAM,0.0200,0.0000
T(位置度4)=TOL/POS,2D,0.0500,RFS
DMESW/COMAND,'TOL-NOM/位置度4,COORD/0,POLTYPE/0,FEAT/圆4,WKPLAN/XYPLAN,XAXIS/15.9115,YAXIS/22.5000,ZAXIS/-3.0000,$
PR/27.5577,PA/54.7329,DIAM/10.0000,XOUTPUT/TRUE,YOUTPUT/TRUE,ZOUTPUT/FALSE,PROUTPUT/FALSE,PAOUTPUT/FALSE,$
DOUTPUT/TRUE,FOUTPUT/FALSE'
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
OUTPUT/FA(圆4),TA(位置度4)
T(位置度5-RN)=TOL/CIRLTY,0.0200
T(位置度5-DF)=TOL/DIAM,0.0200,0.0000
T(位置度5)=TOL/POS,2D,0.0500,RFS
DMESW/COMAND,'TOL-NOM/位置度5,COORD/0,POLTYPE/0,FEAT/圆5,WKPLAN/XYPLAN,XAXIS/31.5000,YAXIS/13.5000,ZAXIS/-3.0000,$
PR/34.2710,PA/23.1986,DIAM/10.0000,XOUTPUT/TRUE,YOUTPUT/TRUE,ZOUTPUT/FALSE,PROUTPUT/FALSE,PAOUTPUT/FALSE,$
DOUTPUT/TRUE,FOUTPUT/FALSE'
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
OUTPUT/FA(圆5),TA(位置度5)
T(位置度6-RN)=TOL/CIRLTY,0.0200
T(位置度6-DF)=TOL/DIAM,0.0200,0.0000
T(位置度6)=TOL/POS,2D,0.0500,RFS
DMESW/COMAND,'TOL-NOM/位置度6,COORD/0,POLTYPE/0,FEAT/圆6,WKPLAN/XYPLAN,XAXIS/47.0885,YAXIS/22.5000,ZAXIS/-3.0000,$
PR/52.1879,PA/25.5396,DIAM/10.0000,XOUTPUT/TRUE,YOUTPUT/TRUE,ZOUTPUT/FALSE,PROUTPUT/FALSE,PAOUTPUT/FALSE,$
DOUTPUT/TRUE,FOUTPUT/FALSE'
DMESW/COMAND,'OUTPUT/UNIT,DIMENSION/MM'
OUTPUT/FA(圆6),TA(位置度6)
NETDMIS5.0 程序结构2023相关推荐
- NETDMIS5.0脱机编程2023
NETDMIS5.0脱机编程功能,用户将测量机,数模,都导入软件中. 在使用导入 CAD 模型进行脱机或联机编程时, 使用虚拟找正功能, 将模型虚拟放置 在机器的某一位置, 方便脱机模拟运行程序. 1 ...
- NETDMIS5.0自动测量圆2023
一自动测量几何元素理论数据的获取 自动测量几何元素需要具备被测元素的理论数据(理论值),得到理论值最方便的方法是直接在工件的CAD模型上进行选取. 对于没有CAD模型的工件,可以根据图样标注获得,将相 ...
- NETDMIS5.0手动测量2023
几何特征(GeometricalFeature)又称几何元素或几何要素,简称特征(Feature)元素或要素,常规几何特征包括:点.直线.平面.圆.圆柱.圆锥.球. 三坐标测量的主要工作是测量各种几何 ...
- NETDMIS5.0端面圆跳动2023
端面圆跳动公差带是在与基准同轴的任一半径位置的测量圆柱面上距离为t的两圆之间的区域: $$ NET_DMIS_20160720 $$ MADE IN DE 2023-2-23 9:25:24 INCL ...
- NETDMIS5.0边界点检测2023
在模型上获得薄壁件的理论数据以便测量薄壁件的变形情况. ( 一次只获得一个边缘点的坐标) 边界点适用于测量棱边的检测,常用于钣金件边缘的检测. " 模式" : 辅助点的测点数设置. ...
- NETDMIS5.0自动测量圆柱2023
对于圆柱的测量,则通过多层圆面采集特征数据. 通过圆柱第一层截面圆心坐标,直径,轴线方向的名义值去测量圆柱. 路径:[基本测量]→[特征测量]→[圆柱] 自动测量圆柱和自动测量圆有很多相同点,不同的是 ...
- NETDMIS5.0自动测量球2023
与其它圆类特征测量不同,球体的特征测量则需要设置两对圆测量参数:球体上经线方 向的的起始角.终止角:球体上纬线方向的起始角.终止角. 经度: 起始角:球体上经度方向的起始角为0 终止角:球体上经度方向 ...
- NETDMIS5.0同轴度测量2023
轴对轴的轴线间同轴度公差要求, 是指被测要素与基准要素均为外圆表面轴线, 其检测时均以其外圆表面体现基准要素和被测要素. 当图样上给出以公共轴线作为基准时, 其误差检测必须 用测量装置体现出公共基准轴 ...
- NETDMIS5.0螺纹孔测量2023
三坐标测量机具有螺纹中心位置测量的功能,可选用柱形测针或球形测针来实现. 柱形测针测量过程简单,易操作,在手动机器和自动机器上均可实现.但在测量时要求测针的轴线方向与螺纹的轴线方向必须相一致,这对测针 ...
最新文章
- 某游戏在华为鸿蒙,部分安卓游戏在华为鸿蒙 OS 上运行，被识别成使用 PC 端模拟器...
- java data使用_@Data注解详解及使用方法-Fun言
- Avahi DOS攻击broadcast-avahi-dos
- MIT人工智能独立设系！拆分EECS为EE、CS、AI+决策三部分，直接归学院管理
- android textwatcher 延时,Java-防止两次在android的textwatcher中运行
- [蓝桥杯2015决赛]穿越雷区-bfs
- C# 解决窗体假死的状态
- SpringCloudStream整合rabbitMq
- centos 虚拟机 使用串口_在VMware虚拟机环境下安装CentOS 7操作系统
- Git之关于本地分支与远程分支
- 为什么我不再推荐使用MVC框架？
- mac终端命令大全介绍
- 基于SpringBoot的社团管理系统的设计与实现
- 教你如何迅速秒杀掉：99%的海量数据处理面试题 1
- missing privilege separation directory /var/empty/sshd问题解决
- GTD时间管理简洁做法
- 微信公众号批量打标签的自动化实现方法
- Ventoy：u盘制作，usb启动盘，超级好用的装机神器
- CSS3属性详解：动画详解
- GreenPlum 大数据平台--运维(三)