f1c100s 128MB W25N01G spi nand调试记录

镜像使用说明

镜像位置images文件夹

uboot-with-spl-usb.bin　FEL模式下使用的uboot镜像

uboot-with-spl-spinand.binspi nand启动使用的uboot镜像

FEL模式下使用标准sunxi-fel执行如下命令

sunxi-fel uboot uboot-with-spl-usb.bin write 0x80000000 uboot-with-spl-spinand.bin

由于sunxi-fel直接写spi nand代码没有调试过，所以直接将uboot镜像传到内存后写入spi nand

执行完成，等待u-boot倒计时完后会自动将uboot-with-spl-spinand.bin写入spi nand中

FEL模式日志

U-Boot SPL 2018.01-g5a65529-dirty (Dec 17 2019 - 15:19:40)

DRAM: 64 MiB

Trying to boot from FEL

U-Boot 2018.01-g5a65529-dirty (Dec 17 2019 - 15:19:40 +0800) Allwinner Technology

CPU: Allwinner F Series (SUNIV)

Model: Lichee Pi Nano

DRAM: 64 MiB

MMC: SUNXI SD/MMC: 0

SPI-NAND: W25N01GV is found size: 128MB.

read status2:0x18

internal ecc is on now turn off

write status2:0x8

read status2:0x8

*** Warning - bad CRC, using default environment

In: serial@1c25000

Out: serial@1c25000

Err: serial@1c25000

Net: No ethernet found.

starting USB...

No controllers found

Hit any key to stop autoboot: 0

SPI-NAND: W25N01GV is found size: 128MB.

read status2:0x18

internal ecc is on now turn off

write status2:0x8

read status2:0x8

SPI-NAND: 1310720 bytes @ 0x0 Updated: OK

SPI-NAND: W25N01GV is found size: 128MB.

read status2:0x18

internal ecc is on now turn off

write status2:0x8

read status2:0x8

SPI-NAND: 2490368 bytes @ 0x80000 Read: OK

Unknown command 'sf' - try 'help'

Wrong Image Format for bootm command

ERROR: can't get kernel image!

=>

因为没有内核所以最后会报错，不用管,烧录完成后spi nand启动日志如下

U-Boot SPL 2018.01-g5a65529-dirty (Dec 17 2019 - 15:20:01)

DRAM: 64 MiB

Trying to boot from sunxi SPI

U-Boot 2018.01-g5a65529-dirty (Dec 17 2019 - 15:20:01 +0800) Allwinner Technology

CPU: Allwinner F Series (SUNIV)

Model: Lichee Pi Nano

DRAM: 64 MiB

MMC: SUNXI SD/MMC: 0

SPI-NAND: W25N01GV is found size: 128MB.

read status2:0x18

internal ecc is on now turn off

write status2:0x8

read status2:0x8

*** Warning - bad CRC, using default environment

In: serial@1c25000

Out: serial@1c25000

Err: serial@1c25000

Net: No ethernet found.

starting USB...

No controllers found

Hit any key to stop autoboot: 0

=>

源码编译

源码编译需要编译两次，分别生成FEL镜像和SPI NAND镜像

首先修改uboot源码下build.sh中交叉编译器

make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- licheepi_nano_spinand_defconfig

make ARCH=arm CROSS_COMPILE=arm-linux-gnueabi- -j8

我的交叉编译工具已经加入到了系统环境变量

生成FEL镜像

修改uboot源码include/configs/sunxi-common.h

打开#define GZYS_USBBURN1定义

#ifndef _SUNXI_COMMON_CONFIG_H

#define _SUNXI_COMMON_CONFIG_H

#include

#include

#define GZYS_USBBURN1

#ifdef CONFIG_OLD_SUNXI_KERNEL_COMPAT

保存后在uboot源码根目录下执行./build.sh进行编译，最后输出信息如下

CC spl/drivers/mtd/spi/sunxi_spi_nand_spl.o

CC spl/drivers/serial/serial.o

CC spl/drivers/serial/serial_ns16550.o

CC spl/drivers/serial/ns16550.o

LD spl/disk/built-in.o

LD spl/lib/built-in.o

LD spl/drivers/serial/built-in.o

LD spl/drivers/mmc/built-in.o

LD spl/drivers/built-in.o

LD spl/u-boot-spl

OBJCOPY spl/u-boot-spl-nodtb.bin

COPY spl/u-boot-spl.bin

MKSUNXI spl/sunxi-spl.bin

BINMAN u-boot-sunxi-with-spl.bin

CFGCHK u-boot.cfg

please delete GZYS_USBBURN in include/configs/sunxi-common.h file and rebuild to create spi nand image

DONE

此时uboot源码根目录下会生成uboot-with-spl-usb.bin文件

生成SPI NAND镜像

修改uboot源码include/configs/sunxi-common.h

注释掉#define GZYS_USBBURN1定义

#ifndef _SUNXI_COMMON_CONFIG_H

#define _SUNXI_COMMON_CONFIG_H

#include

#include

#define GZYS_USBBURN1

#ifdef CONFIG_OLD_SUNXI_KERNEL_COMPAT

保存后在uboot源码根目录下执行./build.sh进行编译，最后输出信息如下

Copying block 23 to 46

1+0 records in

1+0 records out

1024 bytes (1.0 kB, 1.0 KiB) copied, 0.000163137 s, 6.3 MB/s

Copying block 24 to 48

1+0 records in

1+0 records out

1024 bytes (1.0 kB, 1.0 KiB) copied, 0.000174752 s, 5.9 MB/s

Copying block 25 to 50

1+0 records in

1+0 records out

1024 bytes (1.0 kB, 1.0 KiB) copied, 0.000165035 s, 6.2 MB/s

Appending u-boot

984+0 records in

984+0 records out

1007616 bytes (1.0 MB, 984 KiB) copied, 0.00353802 s, 285 MB/s

done

burn uboot-with-spl-spinand.bin to spi nand

cmd is sunxi-fel uboot uboot-with-spl-usb.bin write 0x80000000 uboot-with-spl-spinand.bin

DONE

此时uboot源码根目录下会生成uboot-with-spl-spinand.bin文件

调试中出现的问题及修改

uboot源码增加对w25n01g支持

diff --git a/drivers/mtd/spi-nand/spi-nand-base.c b/drivers/mtd/spi-nand/spi-nand-base.c

index 442a595..bee8a93 100755

--- a/drivers/mtd/spi-nand/spi-nand-base.c

+++ b/drivers/mtd/spi-nand/spi-nand-base.c

@@ -25,6 +25,8 @@ extern int spi_nand_issue_cmd(struct spi_nand_chip *chip, struct spi_nand_cmd *c

int spi_nand_erase(struct spi_nand_chip *chip, uint64_t addr, uint64_t len);

static struct spi_nand_flash spi_nand_table[] = {

+SPI_NAND_INFO("W25N01GV", 0xEF, 0xAA, 2048, 64, 64, 1024,

+1, 1, 0 | SPINAND_NEED_PLANE_SELECT),

SPI_NAND_INFO("GD5F1GQ4UAYIG", 0xC8, 0xF1, 2048, 64, 64, 1024,

1, 1, 0 | SPINAND_USED_GIGADEVICE),

SPI_NAND_INFO("GD5F1GQ4UBYIG", 0xC8, 0xD1, 2048, 64, 64, 1024,

@@ -1844,6 +1846,22 @@ static void spi_nand_set_rd_wr_op(struct spi_nand_chip *chip)

chip->write_cache_rdm_op = SPINAND_CMD_PROG_LOAD_RDM_DATA;

}

}

+//add by leijie for w25n01g turn off internal ecc

+static void w25n01_turn_off_iecc(struct spi_nand_chip *chip)

+{

+u8 buf[1];

+spi_nand_read_reg(chip,0xb0,buf);

+printf("read status2:0x%x\n",buf[0]);

+if(buf[0] & 0x10) {//internal ecc

+printf("internal ecc is on now turn off\n");

+buf[0] = buf[0] & ~(1 << 4);

+printf("write status2:0x%x\n",buf[0]);

+spi_nand_write_reg(chip,0xb0,buf);

+}

+spi_nand_read_reg(chip,0xb0,buf);

+printf("read status2:0x%x\n",buf[0]);

+return;

+}

/**

* spi_nand_init - [Interface] Init SPI-NAND device driver

@@ -1879,8 +1897,9 @@ static int spi_nand_init(struct spi_slave *spi, struct spi_nand_chip **chip_ptr)

return -ENODEV;

ident_done:

-spi_nand_info("SPI-NAND: %s is found.\n", chip->name);

-

+spi_nand_info("SPI-NAND: %s is found size: %dMB.\n", chip->name,chip->size/1024/1024);

+if(id[0] == 0xef)

+w25n01_turn_off_iecc(chip);

// giga-device need re-config rd/wr options

if( chip->options & SPINAND_USED_GIGADEVICE )

spi_nand_set_rd_wr_op(chip);

主要增加了wn25n01内部ecc判断

20191226后面发现spi nand驱动中有对内部ecc进行判断 所以需要把增加的w25n01_turn_off_iecc函数删除,这里源码就不进行更新了

spi nand镜像脚本制作

#!/bin/bash

set -e

[ $# -eq 2 ] || {

echo "SYNTAX: $0 "

echo "Given: $@"

exit 1

}

OUTPUT="$1"

UBOOT="$2"

PAGESIZE=2048

BLOCKSIZE=128

TOOLCHECK=$(od --help | grep 'endia')

if [ "$TOOLCHECK" == "" ]; then

echo "od cmd is too old not support endia"

exit -1

fi

# SPL-Size is an uint32 at 16 bytes offset contained in the SPL header

#uboot header offset head in include/configs/sunxi-common.h CONFIG_SYS_SPI_U_BOOT_OFFS so spl max size is CONFIG_SYS_SPI_U_BOOT_OFFS

#f1c100s modify CONFIG_SYS_SPI_U_BOOT_OFFS to 0xd000(52K)

SPLSIZE=$(od -An -t u4 -j16 -N4 "$UBOOT" | xargs)

printf "SPLSIZE:%d(0x%x)\n" $SPLSIZE $SPLSIZE

# The u-boot size is an uint32 at (0xd000 + 12) bytes offset uboot start offset 0xd000(52K)

UBOOTSIZE=$(od --endian=big -An -t u4 -j$((53248 + 12)) -N4 "$UBOOT" | xargs)

printf "UBOOTSIZE:%d(0x%x)\n" $UBOOTSIZE $UBOOTSIZE

ALIGNCHECK=$(($PAGESIZE%1024))

if [ "$ALIGNCHECK" -ne "0" ]; then

echo "Page-size is not 1k alignable and thus not supported by EGON"

exit -1

fi

KPAGESIZE=$(($PAGESIZE/1024))

SPLBLOCKS=25

echo "Generating boot0 for boot part of max size 0x8000 SPLBLOCKS:$SPLBLOCKS"

dd if="/dev/zero" of="$OUTPUT" bs=1024 count=$((52 - $SPLBLOCKS))

for splcopy in `seq 0 $SPLBLOCKS`;

do

to=$(($splcopy*$KPAGESIZE))

echo "Copying block $splcopy to $to"

dd if="$UBOOT" of="$OUTPUT" bs=1024 count=1 seek=$to skip=$splcopy conv=notrunc

done

echo "Appending u-boot"

dd if="$UBOOT" of="$OUTPUT" bs=1024 seek=52 skip=52 conv=notrunc

sync

echo "done"

其中将页大小和块大小值固定,只传输出文件和输入文件名

由于f1c100s生成的spl镜像sunxi-spl.bin大小为固定值24576个字节，所以简化了脚本

内部brom spi nand启动必需1KB对齐所以将spl镜像放大两倍后小于52KB,暂使用52K这个值

也就是说spl镜像最大为52KB,同时uboot镜像的起始地址为0xd000(52KB)

同时需要修改uboot源码include/configs/sunxi-common.h中的CONFIG_SYS_SPI_U_BOOT_OFFS为0xd000

和CONFIG_SPL_PAD_TO为CONFIG_SYS_SPI_U_BOOT_OFFS

这里有个地方要注意下，如果在FEL模式下运行uboot镜像，需要将CONFIG_SYS_SPI_U_BOOT_OFFS改回0x8000,不然sunxi-fel会报错

启动报错

U-Boot SPL 2018.01-g5a65529-dirty (Dec 17 2019 - 15:20:01)

DRAM: 64 MiB

Trying to boot from sunxi SPI

从spi nand启动卡在上面这个地方，通过加调试信息找到了一个问题

支持spi nand的uboot源码drivers/mtd/spi/sunxi_spi_nand_spl.c

在函数

static u32 sunxi_spi0_read_data中addr默认加了0x8000

需要把这个注释掉

index f70e1ac..0e2a60d 100644

--- a/drivers/mtd/spi/sunxi_spi_nand_spl.c

+++ b/drivers/mtd/spi/sunxi_spi_nand_spl.c

@@ -266,7 +266,7 @@ static u32 sunxi_spi0_read_data(u8 *buf, u32 addr, u32 bufsize,

#ifdef CONFIG_SPINAND

{

u32 ret = bufsize;

-addr += 0x8000;

+//addr += 0x8000; //modify by leijie

int page = addr >> 11;

if( pages != page ) { // need read to cache

writel(4, spi_bc_reg); /* Burst counter (total bytes) */