前言

最近在使用GD32F303的芯片替换STM32F303，自己也在网上查阅了资料但关于具体实现的描述还是较少，希望下面的东西可以帮到大家。

一、原理介绍

在这里不做具体的介绍SPWM实现原理，网上资料很多，简单描述一下控制实现。

硬件：两个高频管，两个工频管。
软件：两个互补定时器通道控制PWM的周期和高频管、工频管的关断方式实现SPWM（正弦波）。

二、代码

1.GD32F303RCT6的PWM配置

代码如下：

void TIM3_Int_Init(u16 arr,u16 psc)
{timer_oc_parameter_struct timer_ocintpara;timer_parameter_struct timer_initpara;rcu_periph_clock_enable(RCU_TIMER3);rcu_periph_clock_enable(RCU_GPIOB);rcu_periph_clock_enable(RCU_AF);gpio_init(GPIOB, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_7);timer_deinit(TIMER3);/* TIMER3 configuration */timer_initpara.prescaler         = psc;timer_initpara.alignedmode       = TIMER_COUNTER_EDGE;timer_initpara.counterdirection  = TIMER_COUNTER_UP;timer_initpara.period            = arr;timer_initpara.clockdivision     = TIMER_CKDIV_DIV1;timer_initpara.repetitioncounter = 0;timer_init(TIMER3,&timer_initpara);/* CH1 configuration in PWM mode1 */timer_ocintpara.ocpolarity   = TIMER_OC_POLARITY_HIGH;timer_ocintpara.outputstate  = TIMER_CCX_ENABLE;timer_ocintpara.ocnpolarity  = TIMER_OCN_POLARITY_HIGH;timer_ocintpara.outputnstate = TIMER_CCXN_DISABLE;timer_ocintpara.ocidlestate  = TIMER_OC_IDLE_STATE_LOW;timer_ocintpara.ocnidlestate = TIMER_OCN_IDLE_STATE_LOW;timer_channel_output_config(TIMER3,TIMER_CH_1,&timer_ocintpara);/* CH1 configuration in PWM mode1,duty cycle 25% */timer_channel_output_pulse_value_config(TIMER3,TIMER_CH_1,2500);timer_channel_output_mode_config(TIMER3,TIMER_CH_1,TIMER_OC_MODE_PWM0);timer_channel_output_shadow_config(TIMER3,TIMER_CH_1,TIMER_OC_SHADOW_DISABLE);timer_primary_output_config(TIMER3,ENABLE);/* auto-reload preload enable */timer_auto_reload_shadow_enable(TIMER3);/* auto-reload preload enable */timer_enable(TIMER3);}

2.GD32F303RCT6的SPWM配置

代码如下：

const unsigned int spwm[200]={
0,117,235,353,470,588,705,823,939,1056,1173,1289,1405,1520,1636,1750,
1865,1979,2092,2205,2317,2429,2540,2651,2760,2870,2978,3086,3193,3299,3404,3509,
3613,3715,3817,3918,4018,4117,4215,4312,4408,4503,4596,4689,4780,4870,4959,5047,
5134,5219,5303,5385,5467,5547,5625,5703,5778,5853,5926,5997,6067,6136,6203,6268,
6332,6394,6455,6514,6572,6628,6682,6735,6786,6835,6883,6929,6973,7015,7056,7095,
7132,7168,7202,7234,7264,7292,7319,7344,7367,7388,7407,7425,7440,7454,7466,7476,
7485,7491,7496,7499,7500,7499,7496,7491,7485,7476,7466,7454,7440,7425,7407,7388,
7367,7344,7319,7292,7264,7234,7202,7168,7132,7095,7056,7015,6973,6929,6883,6835,
6786,6735,6682,6628,6572,6514,6455,6394,6332,6268,6203,6136,6067,5997,5926,5853,
5778,5703,5625,5547,5467,5385,5303,5219,5134,5047,4959,4870,4780,4689,4596,4503,
4408,4312,4215,4117,4018,3918,3817,3715,3613,3509,3404,3299,3193,3086,2978,2870,
2760,2651,2540,2429,2317,2205,2092,1979,1865,1750,1636,1520,1405,1289,1173,1056,
939,823,705,588,470,353,235,117
};
/*------------------------------------------------------------------------------
函数名：TIM0_PWM_Init(u16 arr,u16 psc)
描  述：上管Q1，Q2驱动,下管Q3,Q4驱动互补PWM输出 pb12杀车功能
-----------------------------------------------------------------------------*/void TIM0_PWM_Init(void)
{        timer_oc_parameter_struct timer_ocintpara;      //定时器比较输出初始化结构体timer_parameter_struct timer_initpara;         // 定时器捕获输入初始化结构体timer_break_parameter_struct timer_breakpara;rcu_periph_clock_enable(RCU_GPIOA);rcu_periph_clock_enable(RCU_GPIOB);rcu_periph_clock_enable(RCU_AF);//Configure PA8 PA9 PA10(TIMER0 CH0 CH1 CH2) as alternate functiongpio_init(GPIOA, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_9);                //TIM0CH1高频gpio_init(GPIOA, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_10);               //TIM0CH2工频//Configure  PB14 PB15(TIMER0 CH0N CH1N CH2N) as alternate functiongpio_init(GPIOB, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_14);            gpio_init(GPIOB, GPIO_MODE_AF_PP, GPIO_OSPEED_50MHZ, GPIO_PIN_15);                    gpio_init(GPIOB, GPIO_MODE_IN_FLOATING, GPIO_OSPEED_50MHZ, GPIO_PIN_12);//刹车rcu_periph_clock_enable(RCU_TIMER0);timer_deinit(TIMER0);// TIMER0 configuration timer_initpara.prescaler                  = 0;                                                      //时钟预分频器timer_initpara.alignedmode           = TIMER_COUNTER_EDGE;//TIMER_COUNTER_CENTER_UP;                //计数器触发方式timer_initpara.counterdirection  = TIMER_COUNTER_UP;                                                //计数器模式选择向上计数timer_initpara.period                      = 7500;      //16KHz                                            //定时器周期个数 自动重载值timer_initpara.clockdivision          = TIMER_CKDIV_DIV1;                                           //时钟分频因子timer_initpara.repetitioncounter = 0;                                                               //重复计数值timer_init(TIMER0,&timer_initpara); // CH1 and CH2 configuration in PWM mode timer_ocintpara.outputstate  = TIMER_CCX_ENABLE;                                                   //配置比较输出模式状态(使能或禁止输出)timer_ocintpara.outputnstate = TIMER_CCXN_ENABLE;                                                  //互补比较输出状态timer_ocintpara.ocpolarity   = TIMER_OC_POLARITY_HIGH;                                             //有效电平的极性，可以将有效电平设置成高电平或者低电平timer_ocintpara.ocnpolarity  = TIMER_OCN_POLARITY_HIGH;                                            //互补输出有效极性timer_ocintpara.ocidlestate  = TIMER_OC_IDLE_STATE_LOW;                                            //空闲状态下定时器输出引脚状态timer_ocintpara.ocnidlestate = TIMER_OCN_IDLE_STATE_LOW;                                           //空闲状态定时器互补输出引脚状timer_channel_output_config(TIMER0,TIMER_CH_1,&timer_ocintpara);                  //配置定时器通道输出功能timer_channel_output_config(TIMER0,TIMER_CH_2,&timer_ocintpara);timer_channel_output_pulse_value_config(TIMER0,TIMER_CH_1,0);                     //配置定时器通道输出脉冲值timer_channel_output_mode_config(TIMER0,TIMER_CH_1,TIMER_OC_MODE_PWM0);           //配置定时器通道输出比较模式timer_channel_output_shadow_config(TIMER0,TIMER_CH_1,TIMER_OC_SHADOW_DISABLE);    //配置定时器通道输出影子寄存器timer_channel_output_pulse_value_config(TIMER0,TIMER_CH_2,0);timer_channel_output_mode_config(TIMER0,TIMER_CH_2,TIMER_OC_MODE_PWM0);timer_channel_output_shadow_config(TIMER0,TIMER_CH_2,TIMER_OC_SHADOW_DISABLE);// 自动输出启用、中断、死区时间和锁定timer_breakpara.runoffstate      = TIMER_ROS_STATE_DISABLE;                     //运行模式下输出--禁止timer_breakpara.ideloffstate     = TIMER_IOS_STATE_DISABLE ;                    //空闲模式下输出选择--禁止timer_breakpara.deadtime         = 0x8C;                                        //死区时间1.2ustimer_breakpara.breakpolarity    = TIMER_BREAK_POLARITY_LOW;                    //刹车输入极性timer_breakpara.outputautostate  = TIMER_OUTAUTO_ENABLE;                        //自动输出使能timer_breakpara.protectmode      = TIMER_CCHP_PROT_OFF;                         //锁定设置timer_breakpara.breakstate       = TIMER_BREAK_DISABLE;                         //刹车功能禁止-暂时timer_break_config(TIMER0,&timer_breakpara);// TIMER0 primary output function enable timer_primary_output_config(TIMER0,ENABLE);// auto-reload preload enable timer_auto_reload_shadow_enable(TIMER0);// TIMER0 counter enable timer_enable(TIMER0);}/*------------------------------------------------------------------------------
函数名：TIM2_Int_Init
描  述：
-----------------------------------------------------------------------------*/void TIM2_Int_Init(void)                        //ifreq为不分频时的更新中断频率，psc为预分频值
{timer_parameter_struct  TIM_TimeBaseStructure;rcu_periph_clock_enable(RCU_TIMER2);//定时器TIM2初始化TIM_TimeBaseStructure.period = 4999;                //60HzTIM_TimeBaseStructure.prescaler = 0;                                                  //设置用来作为TIMx时钟频率除数的预分频值TIM_TimeBaseStructure.clockdivision = TIMER_CKDIV_DIV1;                               //设置时钟分割:TDTS = Tck_timTIM_TimeBaseStructure.counterdirection = TIMER_COUNTER_UP;                            //TIM向上计数模式timer_init(TIMER2, &TIM_TimeBaseStructure);                                           //根据指定的参数初始化TIMx的时间基数单位timer_interrupt_enable(TIMER2, TIMER_INT_UP);timer_enable(TIMER2);    nvic_irq_enable(TIMER2_IRQn, 3, 2);}void TIMER2_IRQHandler(void)
{u16 u16TimeCount = 0;if (timer_interrupt_flag_get(TIMER2, TIMER_INT_UP) != RESET)  //检查TIM2更新中断发生与否{       if(u16TimeCount<200){timer_channel_output_pulse_value_config(TIMER0,TIMER_CH_1,spwm[u16TimeCount]);    timer_channel_output_pulse_value_config(TIMER0,TIMER_CH_2,0);++u16TimeCount;}else if(u16TimeCount >= 200 && u16TimeCount<400)    //一周期采样400个点{timer_channel_output_pulse_value_config(TIMER0,TIMER_CH_1,0);timer_channel_output_pulse_value_config(TIMER0,TIMER_CH_2,spwm[u16TimeCount-200]);++u16TimeCount;}else{u16TimeCount = 0;}timer_interrupt_flag_clear(TIMER2, TIMER_INT_UP);  //清除TIMx更新中断标志           }}

int main(void)
{
     GpioInit(); //初始化升压电路控制引脚

TIM0_PWM_Init();
TIM2_Int_Init();
TIM3_Int_Init(9999,11999);            //120M系统时钟--1s
}

总结

以上就是对实现SPWM波形的软件控制代码（已验证），后面还需要控制调制比和步长让波形达到自己电路的输出要求，鉴于大家设计的电路都不一样在这里就不做介绍了。SPWM数组根据自己设置的波形频率需要改变，这个生成工具网上可以下载，有需要的话博主也可以提供。博主是新手，希望各位看官多多包含和提出意见。

GD32F303RCT6PWM及SPWM配置相关推荐

STM32输出SPWM波，HAL库，cubeMX配置，滤波后输出1KHz正弦波
SPWM波对于功率方向,输出SPWM波是必须要掌握的工程: stm32生成spwm代码Keil工程链接资源引用spwm波定义: PWM波形就是指占空比可变的波形:SPWM波形是指脉冲宽度按正弦规 ...
Simulink仿真---SPWM算法
一.概念所谓SPWM,就是让PWM的占空比按正弦规律变化,这样输出波形经过适当的滤波可以做到正弦波输出. SPWM(Sinusoidal PWM)法是一种比较成熟的,目前使用较广泛的PWM法.前面提 ...
电子设计竞赛(三)-SPWM与PID
1 SPWM波调制技术逆变电路的控制方式主要是采用SPWM(正弦脉宽调制技术),IR2104控制开关管的通断来实现正弦调制,SPWM的基本思路是将一个正弦波按等宽间距分成N等份,对于每一个波形 ...
第 40 章呼吸灯与 SPWM 波
40.1 呼吸灯简介呼吸灯,就是指灯光设备的亮度随着时间由暗到亮逐渐增强,再由亮到暗逐渐衰减,很有节奏感地一起一伏,就像是在呼吸一样. 40.2 呼吸灯与 PWM 控制原理呼吸的特性是一种类似图指 ...
PWM和SPWM的区别
最近工作中上接触到PWM和SPWM,虽然这两个名字差不多,但是不管是在功能上还是生成的原理上都是有不同的,包括我们不是很常见的SVPWM波,你们是否也有疑惑这三个之间都有啥关系,今天我们好好分析下它们 ...
SPWM原理及STM32生成
绪论 SPWM在单向逆变器中运用的比较多,在电能与电机控制领域现在大都是用SVPWM.先学好spwm,为以后的进阶做准备!本文主要是我学习spwm的一些理解,然后后通过实例代码生成spwm,可以直接复 ...
DSP28335的SPWM波生成方法
DSP新手,研究了一下午,在这里做个总结,希望对其他刚接触DSP的新手也能有所帮助. 首先要明白SPWM波是什么. SPWM波实际上就只有2种电平,而且其频率一般是你自己给定的,所以难点在于如何调节每 ...
利用28335的epwm产生spwm波的总结
一.SPWM设计简介设计的内容是产生倍频的SPWM波,也即是用的是同一个调制波,两个桥臂上的载波相差180度.产生spwm时,利用TB产生载波,也即是三角波.(计数方式采用增减模式即可),CC中放的 ...
spwm调制c语言程序,SPWM基本原理详解（图文并茂+公式推导+C程序实现）
基本原理 SPWM的全称是(Sinusoidal PWM),正弦脉冲宽度调制是一种非常成熟,使用非常广泛的技术: 之前在PWM的文章中介绍过,基本原理就是面积等效原理,即冲量相等而形状不同的窄脉冲加在 ...

GD32F303RCT6PWM及SPWM配置

文章目录

前言

一、原理介绍

二、代码

1.GD32F303RCT6的PWM配置

2.GD32F303RCT6的SPWM配置

总结

GD32F303RCT6PWM及SPWM配置相关推荐

最新文章

热门文章