UAV-5--链接飞控以及配置SITL以及ardupilot环境

linux系统链接飞控以及配置SITL以及ardupilot环境

先更改本机host到对象的ip

再进行ssh的链接

[外链图片转存失败,源站可能有防盗链机制,建议将图片保存下来直接上传(img-meuTGFrN-1651933771950)(https://s2.loli.net/2022/05/07/eY3L84RVOZF6MrS.png)]

链接成功进入系统

链接飞控

from dronekit import connect # Connect to the Vehicle (in this case a UDP endpoint) 后边那个baud是波特率
vehicle = connect('/dev/ttyUSB0', wait_ready=True, baud=921600) # vehicle is an instance of the Vehicle classprint "Autopilot Firmware version: %s" % vehicle.versionprint "Autopilot capabilities (supports ftp): %s" % vehicle.capabilities.ftpprint "Global Location: %s" % vehicle.location.global_frameprint "Global Location (relative altitude): %s" % vehicle.location.global_relative_frameprint "Local Location: %s" % vehicle.location.local_frame    #NEDprint "Attitude: %s" % vehicle.attitudeprint "Velocity: %s" % vehicle.velocityprint "GPS: %s" % vehicle.gps_0print "Groundspeed: %s" % vehicle.groundspeedprint "Airspeed: %s" % vehicle.airspeedprint "Gimbal status: %s" % vehicle.gimbalprint "Battery: %s" % vehicle.batteryprint "EKF OK?: %s" % vehicle.ekf_okprint "Last Heartbeat: %s" % vehicle.last_heartbeatprint "Rangefinder: %s" % vehicle.rangefinderprint "Rangefinder distance: %s" % vehicle.rangefinder.distanceprint "Rangefinder voltage: %s" % vehicle.rangefinder.voltageprint "Heading: %s" % vehicle.headingprint "Is Armable?: %s" % vehicle.is_armableprint "System status: %s" % vehicle.system_status.stateprint "Mode: %s" % vehicle.mode.name    # settableprint "Armed: %s" % vehicle.armed    # settable

SITL仿真实例

# -*- coding: utf-8 -*-  """
© Copyright 2015-2016, 3D Robotics.
simple_goto.py: GUIDED mode "simple goto" example (Copter Only)
Demonstrates how to arm and takeoff in Copter and how to navigate to points using Vehicle.simple_goto.
"""from __future__ import print_function
import time
from dronekit import connect, VehicleMode, LocationGlobalRelative# 改为当前连接的pixhawk飞控的端口 下边是IP端口
connection_string = '10.42.0.10:14550'
print('Connecting to vehicle on: %s' % connection_string)
# connect函数将会返回一个Vehicle类型的对象，即此处的vehicle
# 即可认为是无人机的主体，通过vehicle对象，我们可以直接控制无人机
vehicle = connect(connection_string,wait_ready=True,baud=921600)# 定义arm_and_takeoff函数，使无人机解锁并起飞到目标高度
# 参数aTargetAltitude即为目标高度，单位为米
def arm_and_takeoff(aTargetAltitude):# 进行起飞前检查  print("Basic pre-arm checks")# vehicle.is_armable会检查飞控是否启动完成、有无GPS fix、卡曼滤波器  # 是否初始化完毕。若以上检查通过，则会返回True  while not vehicle.is_armable:print(" Waiting for vehicle to initialise...")time.sleep(1)# 解锁无人机（电机将开始旋转）  print("Arming motors")# 将无人机的飞行模式切换成"GUIDED"（一般建议在GUIDED模式下控制无人机）  vehicle.mode = VehicleMode("GUIDED")# 通过设置vehicle.armed状态变量为True，解锁无人机  vehicle.armed = True# 在无人机起飞之前，确认电机已经解锁  while not vehicle.armed:print(" Waiting for arming...")time.sleep(1)# 发送起飞指令  print("Taking off!")# simple_takeoff将发送指令，使无人机起飞并上升到目标高度  vehicle.simple_takeoff(aTargetAltitude)# 在无人机上升到目标高度之前，阻塞程序  while True:print(" Altitude: ", vehicle.location.global_relative_frame.alt)# 当高度上升到目标高度的0.95倍时，即认为达到了目标高度，退出循环  # vehicle.location.global_relative_frame.alt为相对于home点的高度  if vehicle.location.global_relative_frame.alt >= aTargetAltitude * 0.95: print("Reached target altitude")break# 等待1s  time.sleep(1)# 调用上面声明的arm_and_takeoff函数，目标高度10m
arm_and_takeoff(10)# 设置在运动时，默认的空速为3m/s
print("Set default/target airspeed to 3")
# vehicle.airspeed变量可读可写，且读、写时的含义不同。
# 读取时，为无人机的当前空速；写入时，设定无人机在执行航点任务时的默认速度
vehicle.airspeed = 3# 发送指令，让无人机前往第一个航点
print("Going towards first point for 30 seconds ...")
# LocationGlobalRelative是一个类，它由经纬度(WGS84)和相对于home点的高度组成
# 这条语句将创建一个位于南纬35.361354，东经149.165218，相对home点高20m的位置
point1 = LocationGlobalRelative(-35.361354, 149.165218, 20)
# simple_goto函数将位置发送给无人机，生成一个目标航点
vehicle.simple_goto(point1)# simple_goto函数只发送指令，不判断有没有到达目标航点
# 它可以被其他后续指令打断，此处延时30s，即让无人机朝向point1飞行30s
time.sleep(30)# 发送指令，让无人机前往第二个航点
print("Going towards second point for 30 seconds (groundspeed set to 10 m/s) ...")
# 与之前类似，这条语句创建了另一个相对home高20m的点
point2 = LocationGlobalRelative(-35.363244, 149.168801, 20)
# simple_goto将目标航点发送给无人机，groundspeed=10设置飞行时的地速为10m/s
vehicle.simple_goto(point2, groundspeed=10)# 与之前一样，延时30s
time.sleep(30)# 发送"返航"指令
print("Returning to Launch")
# 返航，只需将无人机的飞行模式切换成"RTL(Return to Launch)"
# 无人机会自动返回home点的正上方，之后自动降落
vehicle.mode = VehicleMode("RTL")# 退出之前，清除vehicle对象
print("Close vehicle object")
vehicle.close()

仿真会使用到git docker以及ardupilot组件

所以我们对本机进行环境配置

https://github.com/ArduPilot/ardupilot

前往仓库

获取git链接

gitclone

 git clone -b Copter-4.0.7 https://github.com/ArduPilot/ardupilot.git

接着再拉取子模块

eleven@shiyideMacBook-Pro-2 ardupilot % git branch
* （非分支）
eleven@shiyideMacBook-Pro-2 ardupilot % git checkout -b Copter-4.0.7
切换到一个新分支 'Copter-4.0.7'
eleven@shiyideMacBook-Pro-2 ardupilot % git branch
* Copter-4.0.7
eleven@shiyideMacBook-Pro-2 ardupilot % git submodule update --init --recursive

如果遇到失败fail情况

可以直接前往地址下载

[外链图片转存失败,源站可能有防盗链机制,建议将图片保存下来直接上传(img-g376B5aj-1651933771956)(https://s2.loli.net/2022/05/07/MUqCL1YdlKXyN4u.png)]

下载完毕后

进行环境自安装

eleven@shiyideMacBook-Pro-2 ardupilot % cd Tools eleven@shiyideMacBook-Pro-2 Tools % cd environment_install eleven@shiyideMacBook-Pro-2 environment_install % cat install-prereqs-mac.sh

因为我是用的是mac所以选择mac的.sh文件

[外链图片转存失败,源站可能有防盗链机制,建议将图片保存下来直接上传(img-3Y1A88zs-1651933771957)(https://s2.loli.net/2022/05/07/hsMUHcziSAVIeKa.png)]

基本都是安装一些依赖包

可能会有网络问题装不上什么的

多执行几次更改自己的网络条件